Select your language

Engine rebuild with no former experience........

More
5 years 11 months ago #264298 by Racediagnostics
Today I finished lapping the second head, quite a time consuming job.

This image is hidden for guests.
Please log in or register to see it.



I then took them up to the motorbike engine builder, very local, only 5 minuets away. He tested them with petrol in the intake runners and exhaust ports, the were a couple of ports with a very tiny slow weep. He said he would not do any further work on them and would be more than happy. He was amazed that the new guides had gone in so well and maintained concentricity. He had expected that the seats would have had to be re-cut, the workshop had a full set of Nuway cutters but he advised not to do it.

He had a very interesting workshop, and was rebuilding a racing engine with titanium valves......

Next I plan to go through the 80 or so plastic bags with parts in them and remove, clean and catalogue all the nuts and bolts and decide which to replace, re-plate or reuse.

Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: RDele

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago - 5 years 11 months ago #264371 by Racediagnostics
Kim getting ready to do some cataloguing.

[img]hhttps://www.racediagnostics.com/gallery/_data/i/upload/2020/12/08/20201208194900-e70e7edd-la.jpg[/img]

This pile will probably be scrapped, may change my mind when I find out the replacement cost.

This image is hidden for guests.
Please log in or register to see it.



Parts to be plated.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



Parts to be cleaned.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



Now for a bit of excel and to check prices here.

www.belmetric.com/88-yellow-zinc-plated-...u9tjr71q50dt072v8f83

Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 11 months ago by Racediagnostics.

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264372 by Rudiger
Jim, Clean it in Kerosin, bag it and store it away under your work bench.
Rudiger
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264392 by Gullydeckel
Hi Jim,

don't send the cylinder head bolts for plating! They are Nickel coated for low friction coefficient!
Otherwise you have a risk of damage the treads in the crankcase.

Regrads Martin

Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago - 5 years 11 months ago #264406 by Racediagnostics
Hi Martin, yes, all the head bolts have been separated, I will just clean the heads of the external ones and put on some cold bluing.

Well that's most of the hardware ordered from Belmetric in nice yellow passivated zinc, I will re-plate/reuse the M12 nuts and bolts. Trying to plate over 400 items myself would have just taken too long. The cost came in at about £95 for 422 items, however shipping is £40, then import tax will be the final sting in the tail.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 11 months ago by Racediagnostics.
The following user(s) said Thank You: RDele, Chromix

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264409 by Moerten
Impressing work and documentation, Jim. Thanks for that. I have neither the space nor the tools (perhaps some skills...) but I enjoy following all your steps and the progress. I am keen to see it running again and the smile on your face when done.

Thumbs up.

Gruß
Martin
_____________________________________
Lass mich, ich kann das... Oh, kaputt.
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264420 by Chromix
Hi Jim,

I wondered why you mentioned import taxes, checked out Belmetric and saw that they are located in the US. Good grief, you are buying nuts and bolts in the US!!! And even metric ones!! :woohoo:
You could have found them here. I didn't check out all sizes but a few and they were available and they sell them by the piece.
Probably too late for you but maybe interesting for others as well.

Regards,
Lutz

Nimm Dir jeden Tag die Zeit, still zu sitzen und auf die Dinge zu lauschen.
Achte auf die Melodie des Lebens, die in Dir schwingt.
Buddha
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago - 5 years 11 months ago #264424 by Racediagnostics
Hi Lutz, thanks for the link, I will use them for future orders. I had a quick look at the prices, they were ~20% higher than the US supplier, however they may end up being cheaper when import tax and shipping is taken into consideration. Definitely cheaper for small orders.

I had searched for a one stop shop in the UK but had not found a good supplier for yellow passivated zinc.

Looking on the positive side, I saved a fortune by not buying from MB.

Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 11 months ago by Racediagnostics.

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264429 by Racediagnostics
Is there anything I need to take care with when I remove the Fuel Distributer from the part below?

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264437 by Gullydeckel
Hi Jim,

no, nothing special.
You should renew the rubber fuel lines, the material is available for little money:
sternzeit-107.de/de/forum/forum-107/1730...orraum-zum-verteiler
As well you will need to exchange the lower (rubber) part of the Fueldistributor/air vane housing.

Be careful with the small plastic brackets at the fuel lines, they are not longer available, but you can 3D-Print them:
sternzeit-107.de/de/forum/forum-107/2028...ritzleitungen#203684
The STL-file now is located in the download-section.

Regards Martin

Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264465 by Racediagnostics
Hi Martin, that is interesting, surprising that the crimp onto the barb has not been tightened. Seems risky but obviously works.

My hose is marked Cohnen 370, and is ribbed, it looks different to yours. How did you establish the modern equivalent. I wonder if the size is the same for the 450 and 560?

This image is hidden for guests.
Please log in or register to see it.



I will also try to repair the oil cooler hoses.

Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264466 by Racediagnostics
Today I had a closer look at the wear on the rear crankshaft journal.

This image is hidden for guests.
Please log in or register to see it.



Comparison of the old and new seal.

This image is hidden for guests.
Please log in or register to see it.



New seal inserted flush to the surface of the housing.

This image is hidden for guests.
Please log in or register to see it.



From the rear you can see it sits well away from the worn groove.

This image is hidden for guests.
Please log in or register to see it.



Next, more sorting.

Parts to be cleaned or cleaned and painted.

This image is hidden for guests.
Please log in or register to see it.



Parts to be cleaned then zinc plated and yellow passivated.

This image is hidden for guests.
Please log in or register to see it.



I think this lot will take me a few weeks to complete, so no updates for a while.

Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: Marcel, 107_SL, markus1971, RDele, Rudiger

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264733 by Racediagnostics
A few cleaned parts, cleaned with degreaser then a Dremel and metal polish....

This image is hidden for guests.
Please log in or register to see it.



...a few more.

This image is hidden for guests.
Please log in or register to see it.



The external head bolts were a bit corroded.

This image is hidden for guests.
Please log in or register to see it.



Cleaned up on a wire wheel.

This image is hidden for guests.
Please log in or register to see it.

]

Re-blued with "Birchwood Casey".

This image is hidden for guests.
Please log in or register to see it.



After sitting in oil for 12 hours.

This image is hidden for guests.
Please log in or register to see it.



The first batch of parts to be plated were cleaned up, this took most of today as they had so much caked on grease and dirt.

This image is hidden for guests.
Please log in or register to see it.



Rust removal.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



These are the bolts that will be saved and re-plated, sitting in brake cleaner.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264734 by Racediagnostics
Last, does anyone know if these plastic bushes can be removed or are they over-moulded?

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago - 5 years 11 months ago #264799 by Racediagnostics
The parts rinsed and cleaned with a scotch bright pad. A few parts will need a second dip in the acid as I think I put too many parts in at once. Some were sandwiched to close together, however most are good.

This image is hidden for guests.
Please log in or register to see it.



The plating works best on polished parts so I used the wire brush on the first part, this should plate nicely. You can still see where the rust had pitted the surface but I can live with that.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 11 months ago by Racediagnostics.
The following user(s) said Thank You: Rudiger, hhermanski

Please Log in or Create an account to join the conversation.

More
5 years 11 months ago #264858 by Racediagnostics
The nuts and bolts arrived from Belmetric. Nice!

This image is hidden for guests.
Please log in or register to see it.



Finished polishing the parts from yesterday.

This image is hidden for guests.
Please log in or register to see it.



Then polished the fuel pipes.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: KalliSL

Please Log in or Create an account to join the conversation.

More
5 years 10 months ago - 5 years 10 months ago #264910 by messerfloh
Hi Jim, to clean the valves I used a brass bristle wheel on the angle grinder and a lathe with slow turns to get off the grime. Works fine.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.

Scheene Griaß
da Floh


450SLC ´75 Silbergrün
Last edit: 5 years 10 months ago by messerfloh.
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
5 years 10 months ago - 5 years 10 months ago #264964 by Racediagnostics
Today I tried to remove the pulley from the PS pump, however the puller kept slipping off, the manual suggests using a "special tool". So I put it to one side.

This image is hidden for guests.
Please log in or register to see it.



I then moved on to the remaining nuts, bolts and brackets etc.

This image is hidden for guests.
Please log in or register to see it.



More citric acid.

This image is hidden for guests.
Please log in or register to see it.



Back to the PS pump, I tried an alternative approach, I held the pully in one hand and loosened the nut but kept it in place, then hit then end of the tapered shaft with a heavy copper hammer, after 4 increasingly heavy hits it freed off!

This image is hidden for guests.
Please log in or register to see it.



Back to the fasteners, after the citric acid and wire wheel.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 10 months ago by Racediagnostics.
The following user(s) said Thank You: Dr-DJet, KalliSL, RDele, Rudiger, hhermanski

Please Log in or Create an account to join the conversation.

More
5 years 10 months ago - 5 years 10 months ago #264994 by Racediagnostics
I picked up a few more parts from the vapour blaster as well as the ceramic coated exhaust manifolds.

This image is hidden for guests.
Please log in or register to see it.



Then removed the ends of the fuel hoses, fortunately they had not been crimped.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



These parts will be too large for me to plate, so will have to find a good plater locally.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 5 years 10 months ago by Racediagnostics.
The following user(s) said Thank You: hhermanski

Please Log in or Create an account to join the conversation.

More
5 years 10 months ago #265037 by Racediagnostics
Today I removed a few more parts from the engine bay.

This image is hidden for guests.
Please log in or register to see it.



The power steering pipes.

This image is hidden for guests.
Please log in or register to see it.



Heat shields.

This image is hidden for guests.
Please log in or register to see it.



I hope this will be the last batch for citric acid.

This image is hidden for guests.
Please log in or register to see it.



There are a surprising number of pipes and tubes that will need to be plated, these will all be too long for me to do at home, so I will get quotes from professional platers. If it is too expensive, I will plate the ends and then paint the main parts of the pipes.

This image is hidden for guests.
Please log in or register to see it.



Does anyone know what is hidden in the rubber sheathed part of this hose?

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: eglidecascais, Rudiger, hhermanski

Please Log in or Create an account to join the conversation.

Moderators: Ragetti, Obelix116
Time to create page: 0.208 seconds
Powered by Kunena Forum

We use cookies

Cookies make it easier for us to provide you with our services. With the usage of our services you permit us to use cookies and confim our data privacy policy.
CookieHint and Consent by reDim GmbH (Opens in a new window)