- Posts: 1170
- Thank you received: 853
Engine rebuild with no former experience........
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
A set of new pistons and liners would be nice but not really worth it for me and the car.
I am going to investigate the three angle valve job.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
The rod bolts all measure within spec which is 8.0mm minimum (original size is 8.4mm), they were all ~>8.3mm.
This image is hidden for guests.
Please log in or register to see it.
The rod measurements were taken with and without the bearing shells. Using the basic bore sizes and thickness of new bearing shells I can also predict the likely sized when new shells are fitted.
This image is hidden for guests.
Please log in or register to see it.
These are the crankshaft measurements for the main bearings and crankpin bearings. Again, using the basic bore sizes and thickness of new bearing shells I can also predict the likely sized when new shells are fitted.
This image is hidden for guests.
Please log in or register to see it.
Now using the measurements of the crankshaft main bearings and crankpin bearings I can calculate the clearance with the old bearings and what it will likely be with the new bearings.
This image is hidden for guests.
Please log in or register to see it.
As the crankpins measured up ok I went ahead and ordered new standard size big end bearings today, I already bought a set of main bearings some time ago.
Next I will start working on the heads.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
yes I agree doing the same measurement/ check twice and receiving inconsistent results does not make it easier to decide on next steps.
Please find attached a link in respect of flex honing in case your machine shop is hesitant to prep the current liner for the new rings.
blog.brushresearch.com/how-flexible-honi...for-cylinder-sleeves
Liner surface needs to be prepared for the new rings, then the cast iron rings should work good after some running in time.
Usually the Mercedes head should have already a 3 angle valve design.
Just „grinding“ the seats with compound can be ok, you could check with a leak down/ vacuum tester if the seat and valve are leak free.
johnmaherracing.com/tech-talk/3-angle-valve-job/
But I would go for a valve seat cut in the head/ 3 angle design and recut the sealing surface of the valve.
Then the valve and seat are matched with a little use of grinding compound and function is tested with leak down/ vacuum test.
You can use your vacuum device for brake bleeding. Just check if the vacuum remains.
Finally I would check if manifold and head are matching. If not this is an easy way to gain some cheap hp just by matching manifold/ head and gasket with out restrictions.
Nothing to do wrong just check for sufficient wall thickness upfront before you start grinding.
Porting goes deeper into the head , but this is different story and opens another can full of worms.
Kind regards
JP
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Good news, all the wrist pins were in spec.
This image is hidden for guests.
Please log in or register to see it.
As were the rod bush and piston bushes.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Next I started cleaning the cam shaft bearings and the pistons in a degreaser, they cleaned up fairly easily, despite being cleaned in a cold solution at about 6 decC, the weather turned colder today.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Next I measured all the cam towers....
This image is hidden for guests.
Please log in or register to see it.
...and the cam shaft journals.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
The cam bearing clearance are out of spec, the left (from the front of car) bank just over, the right bank worse. New bearing sets are NLA from MB and ~600 a side at places that still have stock.
This image is hidden for guests.
Please log in or register to see it.
Well that is a pita, I will remeasure tomorrow but don't really expect them to be any different. I will search the web tonight to see what I can find.
To take my mind off this I moved on to stripping the heads, but this valve spring compressor wouldn't fit into the valve springs so will pick up a conventional one tomorrow.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Gullydeckel
-
- Offline
- Platinum Member
-
- Posts: 3784
- Thank you received: 1519
removing the valve springs is perfect by this way:
That's how I'm doing that since decades.
Regarding the "bearing-problem": Is the calculated play too high or do you see some wear/damage? Instead of measuring all parts separate, sometime it's more useful to evaluate the play of the assembly and/or compare with the assembly of the other parts which seems to be better/good. Unless you didn't noticed any functional problem or noise up to today and all bearing surfaces are OK it may be still good for doing what it was designed for.
Regards Martin
Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
This image is hidden for guests.
Please log in or register to see it.
Here are a couple of close ups of the worst bearing above cylinder 8, looks like there has been plenty of metal on metal contact.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
I think I could live with the wear on the left side but would like to find an oversize set of bearings for the right side.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
I got back into the garage this afternoon and started work on the first head.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
It was easy to remove the collets as the tool locked in place.
This image is hidden for guests.
Please log in or register to see it.
Six months ago I glued this valve guide in place with high temp loctite, it held for most of the summer but I started getting a puff of smoke on start up again in September, it must have worked its way loose again then.
This image is hidden for guests.
Please log in or register to see it.
Into a bath of hot degreaser.
This image is hidden for guests.
Please log in or register to see it.
Once it had heated up I took the opportunity to remove the remainder of the valve guides.
This image is hidden for guests.
Please log in or register to see it.
Washed and dried.
This image is hidden for guests.
Please log in or register to see it.
I will remove the broken bolt from this tomorrow....
This image is hidden for guests.
Please log in or register to see it.
....and clean up the valves.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Gullydeckel
-
- Offline
- Platinum Member
-
- Posts: 3784
- Thank you received: 1519
your progress is breathtaking!
Did you pounded out the old guides with the hammer? This can be done much softer...
Before you plan to insert the new guides, take a look to the pictures. Getting those parts fitted well needs some prepartion to meet the best fit alignement to the bore. The better the alignement is, the less work on the valve seat is necessary later on.
Cheers Martin
Please log in or register to see it.
Please log in or register to see it.
Please log in or register to see it.
Please log in or register to see it.
Please log in or register to see it.
Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
Please Log in or Create an account to join the conversation.
it's an interesting British Standard version of a hot bath
Good luck with your rebuild!
Thomas
Please Log in or Create an account to join the conversation.
quick question: Where did you bought the yellow tray?
Kind regards
JP
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Rendering Error in layout Message/Item: Kunena\Forum\Libraries\BBCode\KunenaBBCodeLibrary::renderEbayLayout(): Argument #1 ($ItemID) must be of type int, string given, called in /www/htdocs/w01222d8/sternzeit/libraries/kunena/src/BBCode/KunenaBBCode.php on line 313. Please enable debug mode for more information.
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
The valve guide situation is a bit odd, in EPC the original size that was used is no longer available and has been replaced by a fractionally bigger set, EPC refers to these as "repair stage 1", whereas in the workshop manual there is no mention of the original size, it refers to the EPC stage 1 as the "standard dimension". I think that at some stage when Mercedes realised that they had a problem with loose valve guides they dropped the original size and adopted the 1st oversize as the standard replacement.
Here are the old and new guides, I also purchased a single EPC oversize 2 in case I needed it for the problems I had on the intake of cylinder 1.
This image is hidden for guests.
Please log in or register to see it.
You can see here that the old cylinder 1 valve guide easily slips into the head.
This image is hidden for guests.
Please log in or register to see it.
The good news after doing all the measurement is that I wont need to bore out the head for the "oversize 2" valve guide as it is well within the recommend overlap.
This image is hidden for guests.
Please log in or register to see it.
Still got to check the other head but don't expect any issues there.
Next I did an inspection of all the valve seats for damage, good news again there, there were no chips or damage. They are supposed to have a 3 angle grind but its not very obvious.
Cylinder 1 exhaust
This image is hidden for guests.
Please log in or register to see it.
Cylinder 1 intake.
This image is hidden for guests.
Please log in or register to see it.
The remainder of the valve seats on the first head were the same.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Gullydeckel wrote: Hi Jim,
Getting those parts fitted well needs some prepartion to meet the best fit alignement to the bore. The better the alignement is, the less work on the valve seat is necessary later on.
Cheers Martin
Hi Martin, I will use your more gentle method for the installation. Did you have any thoughts on the picture of the close up picture of the CAM and bearing?
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
First I stripped down the second head.
This image is hidden for guests.
Please log in or register to see it.
The tray is now full!
This image is hidden for guests.
Please log in or register to see it.
Next was a lot of scrubbing in the hot degreaser bath.
This image is hidden for guests.
Please log in or register to see it.
I then checked both heads for flatness, both were good. but both heads don't look great, do you think they will seal ok or do they need skimmed?
This image is hidden for guests.
Please log in or register to see it.
Next I went back to the sheared bolt on the first head.
This image is hidden for guests.
Please log in or register to see it.
Built up with weld.
This image is hidden for guests.
Please log in or register to see it.
Then nut welded on.
This image is hidden for guests.
Please log in or register to see it.
I managed to get the bolt turning but had to go through this process a lot of times. I think the thread has galled since I am making such slow progress.
This image is hidden for guests.
Please log in or register to see it.
It is now sitting in a puddle of "plus gas" overnight to see if that helps.
I then went on to try to clean up the valves, I will leave them in this oven cleaner overnight, but don't have a good feeling of success. The main ingredient is Potassium Hydroxide. Does anyone have a suggestion of the best way to do this?
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Gullydeckel
-
- Offline
- Platinum Member
-
- Posts: 3784
- Thank you received: 1519
the camshaft bearing looks not so fine, but it may be worth a try. I wonder how this damage starts, it's the bearing closest to the oil support. The highest stress probably has the bearing on the other end, where the load of the timing chain is on. On this side I would make no compromise.
When you press in the new guides using a threaded rod, you need to lubricate the thread very well. Change the nut from time to time, as well it’s necessary to prepare a couple of thread bar pieces in advance. The stress is very high so you need to change the parts from time to time. I used copper pipes to prevent the cylinder head from damage. The copper as well won’t be very durable.
Later on try to grind as little as possible from the valve seats! The more you grind, the more new shims you need and these little things are very expensive.
Greetings Martin
Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
Please Log in or Create an account to join the conversation.
smoke resin remover works very well.
One Liter in a bowl and then let time do the job.
After two days most valves were pretty clean and needed only minor add cleaning.
Kind regards
JP
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
Forum Latest
-
- Mengenteiler einstellen
- In Mercedes-Benz R/C 107 SL forum by Joscho80 8 hours 37 minutes ago
-
-
- Türverkleidung / Türpappen
- In Mercedes-Benz R/C 107 SL forum by Uwe E. 14 hours 59 minutes ago
-
-
-
- Nabe für Nardi Lenkrad
- In Mercedes-Benz R/C 107 SL forum by Heiner107 16 hours 53 minutes ago
-
-
-
- Hinterachse
- In Mercedes-Benz R/C 107 SL forum by Ragetti 18 hours 4 minutes ago
-
-
-
- Schweiz kehrt zu UKW zurück
- In Sonstige FliWaTüt Oldtimer Themen by Albuchler 19 hours 28 minutes ago
-
-
-
- Benzingeruch im Kofferraum R107 geht nicht weg
- In Mercedes-Benz R/C 107 SL forum by wusel-53 21 hours 23 minutes ago
-
-
-
- Schraube Anschlag Deckel Handschuhfach
- In Mercedes-Benz R/C 107 SL forum by plumpa 1 day 9 hours ago
-
-
-
- Mercedes Sammlung unterm Hammer
- In Sonstige FliWaTüt Oldtimer Themen by Neckartaler 1 day 18 hours ago
-
-
- Frage zur sogenannten WIS CD
- In Mercedes-Benz R/C 107 SL forum by Tilman 2 days 11 hours ago
-
-
- Nockenwelle recht 500SLC
- In Mercedes-Benz R/C 107 SL forum by T-Modell 2 days 15 hours ago
-
Letzte Artikel
Sun visor repair
Racediagnostics - 05 September 2021Jim did a full restore of his car and of course he did not like his sun visors to be old bumpy...
Hinterachs Differential / transmission ratio R/C...
Dr-DJet - 11 April 2021im Rahmen der Tacho Recherchen stellte ich fest, dass es nirgendwo richtig oder nur...
Checking and repairing mono valve or duo valve...
Dr-DJet - 18 November 2018It took till September 1981 that R107 SL received a heating system with pulsed mono or duo valves...
Polstercode SLC Verwendet 1979 - 1981
Frank25 - 30 September 2018Ihr wollt wissen, wie Euer Stoff-, MB-Tex oder Lederpolster von 1979-1981 ausgesehen hat? Frank...
Datenschutzerklärung
Sternzeit-107 - 06 June 2018Neue Datenschutzrichtlinie nach EU-DSGVO / New data privacy declaration according to EU directives...
Latest Articles (many more in DE)
Sun visor repair
Racediagnostics - 05 September 2021Jim did a full restore of his car and of course he did not like his sun visors to be old bumpy...
Hinterachs Differential / transmission ratio R/C...
Dr-DJet - 11 April 2021im Rahmen der Tacho Recherchen stellte ich fest, dass es nirgendwo richtig oder nur...
Checking and repairing mono valve or duo valve...
Dr-DJet - 18 November 2018It took till September 1981 that R107 SL received a heating system with pulsed mono or duo valves...
Polstercode SLC Verwendet 1979 - 1981
Frank25 - 30 September 2018Ihr wollt wissen, wie Euer Stoff-, MB-Tex oder Lederpolster von 1979-1981 ausgesehen hat? Frank...
Datenschutzerklärung
Sternzeit-107 - 06 June 2018Neue Datenschutzrichtlinie nach EU-DSGVO / New data privacy declaration according to EU directives...