- Posts: 1170
- Thank you received: 853
Engine rebuild with no former experience........
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
This image is hidden for guests.
Please log in or register to see it.
Released the gear linkage.
This image is hidden for guests.
Please log in or register to see it.
Removed the front part of the cradle.
This image is hidden for guests.
Please log in or register to see it.
Kick-down wire removed.
This image is hidden for guests.
Please log in or register to see it.
Remainder of cradle removed.
This image is hidden for guests.
Please log in or register to see it.
Speedometer cable and PNDR switch harness released.
This image is hidden for guests.
Please log in or register to see it.
Prop-shaft coupling released.
This image is hidden for guests.
Please log in or register to see it.
For the prop-shaft spline coupling.
This image is hidden for guests.
Please log in or register to see it.
Finally the torque converter was drained.
This image is hidden for guests.
Please log in or register to see it.
That's all the prep work now almost complete.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Protection for the radiator support.
This image is hidden for guests.
Please log in or register to see it.
Make your bets now, will the engine come out with the bonnet on or not?
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
It's up as far as I dare.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
At least I would try to hold it from the ceiling. Otherwise, if you interfere with one of the supports while taking the engine out, bad things could happen to it.
Regards, Lutz
Nimm Dir jeden Tag die Zeit, still zu sitzen und auf die Dinge zu lauschen.
Achte auf die Melodie des Lebens, die in Dir schwingt.
Buddha
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Taking the bonnet off with my wife would be a high risk, it is so easy to scratch or dent a wing etc. If she struggles with the weight.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
Rudiger
Please Log in or Create an account to join the conversation.
- Thomas2509
-
- Offline
- Junior Member
-
- Posts: 86
- Thank you received: 39
It is easy to remove and you need the space.
And take a additional look to the transmission. I forgot one wiring harness connection at the transmission and damaged the connector.
Best regards Thomas
Es grüßt herzlich
Thomas
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
This image is hidden for guests.
Please log in or register to see it.
The car pushed out of the garage a bit to allow the engine hoist to be positioned.
This image is hidden for guests.
Please log in or register to see it.
The bonnet support felt very secure in this position, ready to lift.
This image is hidden for guests.
Please log in or register to see it.
It took nearly an hour to get the engine into this position, it kept jamming between the right exhaust manifold against the chassis rail and the bell housing on the steering box. In the end I had to remove the exhaust manifold on the right which took a at least 30 minutes due to the position of its fixing. You can also see from this picture it was wise to remove the fuel distributer etc.
This image is hidden for guests.
Please log in or register to see it.
From then on it was straightforward to raise the engine, level it and drop the car onto its wheels then push it back out of the way.
This image is hidden for guests.
Please log in or register to see it.
Engine dropped onto a trolley.
This image is hidden for guests.
Please log in or register to see it.
Next I dragged the car lift back into place.
This image is hidden for guests.
Please log in or register to see it.
I then assembled the engine stand and had a tidy up.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
You can see here the problem area where the bell housing fouled against the steering box. I will trim some of this off to improve clearance.
This image is hidden for guests.
Please log in or register to see it.
I videoed the entire extraction but will need to edit/fast forward some sections as it's 90minutes long and rather boring.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Seewolf107
-
- Offline
- Senior Member
-
- Posts: 610
- Thank you received: 189
It is not that hard.
Grüsse Claus
1966 Plymouth Belvedere 383, 300D 1983, 280CE W123
Please Log in or Create an account to join the conversation.
- markus1971
-
- Offline
- Senior Member
-
- Posts: 725
- Thank you received: 162
you did a great job! Can you estimate the high to the ceiling that is needed to remove the engine?
Best regards
Markus
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- markus1971
-
- Offline
- Senior Member
-
- Posts: 725
- Thank you received: 162
best regards Markus
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Engine lifted again.
This image is hidden for guests.
Please log in or register to see it.
First task was to remove the trans oil cooler pipes.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Then the starter motor.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Spark plugs, not looking too good, especially No1 that has had the valve guide issue. They look like they have been running too rich but CO level is on target at 1%, so burning oil from somewhere.
This image is hidden for guests.
Please log in or register to see it.
Transmission dip stick, tube, vacuum line and shift rod removed.
This image is hidden for guests.
Please log in or register to see it.
Torque converter bolts removed via the starter motor aperture.
This image is hidden for guests.
Please log in or register to see it.
Transmission bolts removed and lifted back off, but the torque converter stayed in place.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
This image is hidden for guests.
Please log in or register to see it.
The trans had been leaking pink fluid from the bottom of the bell housing last year till I put in some snake oil which seems to have fixed the problem. I'll replace both the shaft and pump seal though.
This image is hidden for guests.
Please log in or register to see it.
I then locked up the crank shaft at the front to remove the flex plate.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
Rear cover removed.
This image is hidden for guests.
Please log in or register to see it.
Crank seal plate removed.
This image is hidden for guests.
Please log in or register to see it.
Finally the harmonic balancer bolt on the front of the crank. I bolted this lever on to the rear of the crank and asked Kim to stand on it while I unbolted the front, it came of easily.
This image is hidden for guests.
Please log in or register to see it.
This image is hidden for guests.
Please log in or register to see it.
The first task tomorrow will be to fabricate a frame for this old TV to sit in to display the workshop manual in portrait mode.
This image is hidden for guests.
Please log in or register to see it.
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
- Racediagnostics
- Topic Author
- Offline
- Premium Member
-
- UK spec
- Posts: 1170
- Thank you received: 853
Has anyone used a sleeve here before?
This image is hidden for guests.
Please log in or register to see it.
www.partsgeek.com/catalog/1980/mercedes/...t_repair_sleeve.html
www.rockauto.com/en/catalog/mercedes-ben...+repair+sleeve,10524
Cheers
Jim
1979 450SL - 2008 911 Turbo
Please Log in or Create an account to join the conversation.
Just use some 10 weight engine oil on the inside.
Rudiger
Please Log in or Create an account to join the conversation.
- Gullydeckel
-
- Offline
- Platinum Member
-
- Posts: 3784
- Thank you received: 1519
don't do that (now). Just install the new seal ring with 1 or 2mm offset compared to the former seal lip position.
I know from other engines, that for maintenance complete seal assemblies are offered where the seal ring is pressed in on a different axial position by manufacturer. Just to avoid the interference with the old running mark.
Modern seals are made from PTFE with a total different lip design and not produce marks like that anymore.
Best regards Martin
Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte
Please Log in or Create an account to join the conversation.
is it possible to position the new seal just 1-2 mm off the former position? Doesn't the seal want to move back to its former position into the groove?
Regards,
Lutz
Nimm Dir jeden Tag die Zeit, still zu sitzen und auf die Dinge zu lauschen.
Achte auf die Melodie des Lebens, die in Dir schwingt.
Buddha
Please Log in or Create an account to join the conversation.