Select your language

Engine rebuild with no former experience........

More
6 years 6 days ago #262087 by wusel-53
Hi Lutz, hi Jim,

I think, it would be possible. When I changed the seal, it was so hard to get the seal in right Position. I can't belive, that the seal move back in the groove.

Viele Grüße

Thorsten

Man lernt nie aus
380SL (US-Version, Bj.84), Eura-Wohnmobil und ein ebike :-)
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago #262088 by Richard64
Hey Jim,

in this case you need an other Crankshaft-Seal. The Part-Numer ist A 120 997 02 46. This Seal has, in the same position as the old one, an offset of 1,5 mm at the main Lip.

Gruß Richard

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago #262090 by Gullydeckel
Hi Lutz,

the seal lip design is very stiff in longitudinal direction and about 2mm are enough.
But this space at least must be available. At sealing diameters of this size installing a new seal at old position is not recommended!

Regards Martin

Ich bin jetzt in dem Alter wo ich meine Fehler zugeben könnte - wenn ich welche hätte

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago - 6 years 6 days ago #262091 by wusel-53
I think I have read in the WIS, that there is a repair size if the seal has made a groove

Viele Grüße

Thorsten

Man lernt nie aus
380SL (US-Version, Bj.84), Eura-Wohnmobil und ein ebike :-)
Last edit: 6 years 6 days ago by wusel-53.
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago #262107 by Rudiger
It’s called “offset shaft seal”. Offset simmering.
Rudiger
The following user(s) said Thank You: Racediagnostics, wusel-53

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago - 6 years 6 days ago #262113 by Racediagnostics
I found that the replacement seals are slightly less deep than the original which should put the seal surface just behind the damaged surface. The original seal is 13mm deep and the replacement is ~10mm.

This image is hidden for guests.
Please log in or register to see it.



I did run into a problem today, two seized bolts, more details on that later.

In the mean time here is a video of the engine being removed.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 6 years 6 days ago by Racediagnostics.

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago #262120 by Racediagnostics
More progress today but then I hit a problem, two long cap head bolts that have seized and are rounded off, more on that later.

Pulley and balancer removed, Someone has been in here before me to try to repair a front seal oil leak.

This image is hidden for guests.
Please log in or register to see it.



The oil leak!

This image is hidden for guests.
Please log in or register to see it.



Engine transferred onto the stand.

This image is hidden for guests.
Please log in or register to see it.



Pulling the crank hub off.

This image is hidden for guests.
Please log in or register to see it.



It has a deep groove also, someone had been in here before me and fitted a new seal which wasn't working too well.

This image is hidden for guests.
Please log in or register to see it.



A look at the timing.

Crank on 0 degrees.

This image is hidden for guests.
Please log in or register to see it.



Left CAM.

This image is hidden for guests.
Please log in or register to see it.



Right CAM.

This image is hidden for guests.
Please log in or register to see it.



With the left cam lined up then the balancer shows this.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago - 6 years 6 days ago #262121 by Racediagnostics
Some more parts removed, one small screw sheared off, that should be easy to remove or drill out.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



Water pump removed.

This image is hidden for guests.
Please log in or register to see it.



Front of the engine stripped.

This image is hidden for guests.
Please log in or register to see it.



OK, so here is the problem, there are two of the cap head bolts both at the rear of the intake manifold that are seized. As you can see they are long, I tried map gas and gentle pressure, then an impact and they stripped out.

This image is hidden for guests.
Please log in or register to see it.



My plan is to weld on a big nut but from the way they felt I think the bolt will shear off at some point along the shaft. Because they are at an odd angle the manifold will not lift off if they shear above the level of the head.

Any suggestions?

Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 6 years 6 days ago by Racediagnostics.
The following user(s) said Thank You: 107_SL, RDele

Please Log in or Create an account to join the conversation.

More
6 years 6 days ago #262141 by Rudiger
With some luck the heat from the welding will loosen the bolt up. Try penetration oil and let it sit over night.
Rudiger
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
6 years 5 days ago #262226 by Uncle Benz
Try giving it a few whacks downwards with a large hammer and a punch. Often a shock might loosen it.

Regards
Stian
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

More
6 years 5 days ago #262238 by Racediagnostics
Well positive and negative, here is how it went today.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
6 years 5 days ago #262240 by Racediagnostics
This is the bolt that made it out.

This image is hidden for guests.
Please log in or register to see it.



The one I had to cut off, I think I will be able to get this out fairly easily. Th good news is there was no damage to the head.

This image is hidden for guests.
Please log in or register to see it.



The other side.

This image is hidden for guests.
Please log in or register to see it.



The damaged intake manifold. It's not going to be easy to get the shaft of the bolt out. Once it is out, I will need to get someone to TIG weld the damaged area to repair it. There also looks to have been a bit of corrosion to the surfaces where coolant was washing against the surface and leaking under the gasket.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: Chromix

Please Log in or Create an account to join the conversation.

More
6 years 3 days ago #262390 by Racediagnostics
More table space set up.

This image is hidden for guests.
Please log in or register to see it.



Removed the rocker arms.

This image is hidden for guests.
Please log in or register to see it.



This was a good investment.

This image is hidden for guests.
Please log in or register to see it.



Next I decided to get the dip stick tube out of the way.

This image is hidden for guests.
Please log in or register to see it.



It came out easier than expected.

This image is hidden for guests.
Please log in or register to see it.



Then the tensioner.....

This image is hidden for guests.
Please log in or register to see it.



...and manifold.

This image is hidden for guests.
Please log in or register to see it.



Using a strong magnet to ensure the chain circlips don't go missing.

This image is hidden for guests.
Please log in or register to see it.



Releasing the cam shaft bolts.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
6 years 3 days ago #262391 by Racediagnostics
Removing the chain guides, these ones are ten years old.

This image is hidden for guests.
Please log in or register to see it.



Not much wear.

This image is hidden for guests.
Please log in or register to see it.



Refreshing my memory before taking the heads off.

This image is hidden for guests.
Please log in or register to see it.



First head, cylinders 5 to 8.

This image is hidden for guests.
Please log in or register to see it.



Other head, cylinders 1 to 4, you can see cylinder 1 which had the valve guide problem has the most build up and is oily.

This image is hidden for guests.
Please log in or register to see it.



Surprisingly, it also has the cleanest piston???

This image is hidden for guests.
Please log in or register to see it.



The bores all look in reasonable condition with the cross hatching still visible to some degree.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



Curved guide removed.

This image is hidden for guests.
Please log in or register to see it.



That's it for today.

This image is hidden for guests.
Please log in or register to see it.



I did try to remove the front cover, all the bolts are out but it didn't want to come off so I will investigate more tomorrow. Perhaps the oil pan needs to come off first.

Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: Marcel, KalliSL, louisB, 107_SL, markus1971, Chromix, texasdriver560, Teppich58, ramses+

Please Log in or Create an account to join the conversation.

More
6 years 2 days ago #262449 by Racediagnostics
Sump off first thing today.

This image is hidden for guests.
Please log in or register to see it.



There were a few plastic bits in the cruddy oil at the bottom of the sump.

This image is hidden for guests.
Please log in or register to see it.



Bits of chain guide rail.

This image is hidden for guests.
Please log in or register to see it.



It is what it is.

This image is hidden for guests.
Please log in or register to see it.



Oil pump off.

This image is hidden for guests.
Please log in or register to see it.



I couldn't get the front cover off till I spotted this bolt.:doh:

This image is hidden for guests.
Please log in or register to see it.



The lower chain guides which have never been changed in 41 years.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



The oil pump chain looks to be in good condition, all the links are tight so I wont replace unless there is good advice to.

This image is hidden for guests.
Please log in or register to see it.



Timing cover with the idler wheel at the top and distributer cog on the left.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo

Please Log in or Create an account to join the conversation.

More
6 years 2 days ago #262450 by Racediagnostics
Lucky I bought a new idler wheel, two broken teeth.

This image is hidden for guests.
Please log in or register to see it.



Oil pump chain tensioner also 41 years old and worn.

This image is hidden for guests.
Please log in or register to see it.



Measuring the big end end axial float and then crank axial end float.

Crank was 0.21mm vs limit of 0.3mm

Big ends were 0.29 to 0.33mm vs limit of 0.5mm

This image is hidden for guests.
Please log in or register to see it.



Pulling off the crankshaft sprocket.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



Seven of the pistons were 91.99mm.

This image is hidden for guests.
Please log in or register to see it.



Just one was 92.05mm, which is at the large end of the standard sized pistons.

This image is hidden for guests.
Please log in or register to see it.



The last thing I did was remove the first big end bearing cap nuts, but the cap didn't want to come off. I gave the studs a light taps but it didn't break free. Any suggestions on how to free it off without damage?

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
The following user(s) said Thank You: Marcel, louisB, 107_SL, markus1971, RDele, Chromix, texasdriver560

Please Log in or Create an account to join the conversation.

More
6 years 2 days ago #262452 by markus1971
Hello Jim,

very good ducumentation of your work, thank you for that. It will help me very much when i will exchange the chain guides of my engine.
Good luck for continuing the work,

Best regards Markus

Please Log in or Create an account to join the conversation.

More
6 years 1 day ago - 6 years 1 day ago #262511 by Racediagnostics
I removed the pistons first today, the caps are held on tightly even once the nuts are removed, an interference fit between the cap and the lower portion of the studs. It took a bit of courage to separate the first one.

This image is hidden for guests.
Please log in or register to see it.



There is some slight scoring on the top side of the pistons, I was surprised that the underside was clear. Left bank viewed from the front of car.

This image is hidden for guests.
Please log in or register to see it.



Right side.

This image is hidden for guests.
Please log in or register to see it.



Main bearing sizes, only four shown but there are five bearings?

This image is hidden for guests.
Please log in or register to see it.



Before removing the caps I made this video.



This image is hidden for guests.
Please log in or register to see it.



Crankshaft lifted out.

This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.



This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 6 years 1 day ago by Racediagnostics.
The following user(s) said Thank You: merc450, Chromix, Scenic, ramses+, Drachenlord

Please Log in or Create an account to join the conversation.

More
6 years 1 day ago - 6 years 1 day ago #262512 by Racediagnostics
After I measure the main bearings and piston bores I plan to send the block out to be cleaned at a machine shop, should I remove the pressure release valves or is it ok to leave them in place?

These two are the main over pressure release valve and the oil cooler over pressure valve.

This image is hidden for guests.
Please log in or register to see it.



This one is the oil filer pressure relief valve.

This image is hidden for guests.
Please log in or register to see it.


Cheers
Jim

1979 450SL - 2008 911 Turbo
Last edit: 6 years 1 day ago by Racediagnostics.
The following user(s) said Thank You: KalliSL, merc450, texasdriver560

Please Log in or Create an account to join the conversation.

More
6 years 1 day ago - 6 years 1 day ago #262513 by Rudiger
Jim take everything off. After you get the block back clean all the water chanels and oil chanels. I use a brush to clean my rifles and guns. I'm taking from bad $$$ experiences.
Rudiger
Last edit: 6 years 1 day ago by Rudiger.
The following user(s) said Thank You: Racediagnostics

Please Log in or Create an account to join the conversation.

Moderators: Ragetti, Obelix116
Time to create page: 0.194 seconds
Powered by Kunena Forum

We use cookies

Cookies make it easier for us to provide you with our services. With the usage of our services you permit us to use cookies and confim our data privacy policy.
CookieHint and Consent by reDim GmbH (Opens in a new window)