Sprache auswählen

Engine rebuild with no former experience........

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
31 Okt. 2020 00:53 - 31 Okt. 2020 01:00 #261449 von Racediagnostics
Engine rebuild with no former experience........ wurde erstellt von Racediagnostics
The time has come, I plan to rebuild my engine as I need to take it out of the car to paint the engine bay. It has a few issues, leaking rear main seal and head gaskets etc, so while it is out of the car I will take the opportunity to carry out a full rebuild. I have also had an issue with a loose valve guide so I will be able to fix this at the same time, on top of this I am sure I am down on power since I installed this engine ten years ago.

My garage space is very limited so I decided to put my XK8 into storage over the winter to free us space to work on the engine. I drove it to the storage location on Wednesday, it was a large grain store on a remote farm and was dry and extremely warm inside.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Yesterday I moved the car lift out of the way and retrieved the engine crane from the shed and had a freak accident!

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



I was using this pry bar to lever up one end of the car lift to fit its castor wheels to move it, I levered it up to put a block of wood under the frame and left bar down where I had used it.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Next the lift slipped off the block of wood, fell about 5cm and landed on the pry bar and propelled it through the air, into my head!

Ouch!

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Back to it today, I jacked up the car and the supported under the chassis rails.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Then drained the fluids and removed the radiator.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Since there have been a few scare stories about car stands I decided to put another two stands under the sills without any weight on them as a backup, that will give me more confidence when working underneath.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



To get some knowledge about engine building, I bought this US book, its not ideal for the MB engine but does cover all of the basics.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



The weather is bad tomorrow so will make some more progress.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 31 Okt. 2020 01:00 von Racediagnostics.
Folgende Benutzer bedankten sich: Marcel, 107_SL, Ernest, texasdriver560, mike 560

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Okt. 2020 03:02 - 31 Okt. 2020 03:58 #261450 von Rudiger
Jim, to overhaul an engine is pretty straight forward. Basically intake manifold, heads and block. Get the specs and tolerances and you are good. WIS should be in eye side. :)

Remember wisely-53 Thorsten overhauled a transmission. He is a pencil pusher at the fed. Government. WIS will help.
Btw, I wouldn’t touch a damn automatic transmission with a 10 foot pole
Rudiger
Letzte Änderung: 31 Okt. 2020 03:58 von Rudiger.
Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Okt. 2020 03:15 #261451 von Caymus
Hi Jim,

I love your “ I can do it attitude “ a complete Engine rebuild without having it done before, chapeau.
I hope you have also mechanical capacity somewhere available to machine or grind the joint faces Motor block cylinder head if necessary or to hone the cylinders if you have to replace the pistons with oversized ones.
A recommendation I got from a friend of mine, a mechanic, is when you start to disassemble the intake manifold mark every screw you take out with a sequential number and mark the same number on the hole in the manifold with a permanent marker. That is extremely helpful based on the different length of the screws when you have to reassemble. And take photos, photos and more photos. But whom am I telling this with your experience.
I guess you have a motor stand like this one to carry the motor block for the rebuild work. www.harborfreight.com/2000-lbs-capacity-...ine-stand-69522.html
I wish you all the best for your project and may the accident you have had will be the only one.
Please keep us posted with your progress.

Liebe Gruesse
Bernd

"Why let somebody else screw it up for parts and labor when you can screw it up for just parts?"

“ Wer bei uns anderen sagt, wo es langgeht, sollte das schon wegweisend tun.”
Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Okt. 2020 07:10 #261457 von Hannesmann
Hi Jim,
if the guy on the book is the one from "home improvement/hör mal wer da hämmert) you should know that not everything they did was working :P .
Just a joke >> I'm sure you will fix it !
Gruss
Achim

350 SLC Bj 78,

Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Okt. 2020 11:42 #261467 von Chromix
Hi Jim,

good luck with the job and hopefully no more freak accidents.
The one you had now is kind of typical: a few incidents that subsequentially occur and that you alltogether never had on your radar.
Please keep us updated, I think most of the people here like your stories and appreciate them.

Regards, Lutz

Alle Lebewesen außer den Menschen wissen, daß der Hauptzweck des Lebens darin besteht, es zu genießen.
Samuel Butler
Folgende Benutzer bedankten sich: texasdriver560, Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
31 Okt. 2020 21:10 #261516 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Folgende Benutzer bedankten sich: Caymus

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
31 Okt. 2020 21:32 #261517 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
I spent a few hours in the garage today,

The first job was to drain the PS pump.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Then remove the PS oil cooler, I had to disconnect the lower valance to get it out. I am removing more than would be needed just to remove the engine as I plan to paint the engine bay.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Both removed.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Then battery and tray removed to give access to the top of the exhaust.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



This spanner is good for the right manifold.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



H pipe and damper removed.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Does anyone know the optimal height to raise the front of the car to make the engine and transmission removal trouble free?

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Folgende Benutzer bedankten sich: mike 560

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
31 Okt. 2020 22:16 - 31 Okt. 2020 22:17 #261519 von Rudiger
Jim, how much headroom do you have? Are you taking engine and transmission simultaneously out? Do you have a load leveler? Do you take the hood, bonnet, off?
www.harborfreight.com/2-ton-capacity-hea...psugg_q=engine+hoist
Rudiger
Letzte Änderung: 31 Okt. 2020 22:17 von Rudiger.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
31 Okt. 2020 23:04 - 31 Okt. 2020 23:06 #261524 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
The headroom is 2.6m, the engine and transmission will come out together, and yes I have a load leveler. I had planned to remove the bonnet until I saw this picture.

www.benzworld.org/threads/removing-the-e...read-2269986&slide=0

I have removed the old engine ten years ago but don't remember exactly how high I raised it but remember I had a bit of trouble with the transmission hitting the floor of the garage.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



There must be an optimal height, enough to clear the transmission but not too high for the hoist.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 31 Okt. 2020 23:06 von Racediagnostics.
Folgende Benutzer bedankten sich: Caymus, mike 560

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Nov. 2020 10:49 #261529 von Stuntman Mike
Hi Jim,

did you consider taking the motor out from the bottom?

When I removed the engine from my 968CS it figured out that it was much more comfortable to dismantle the front suspension and lower the motor to the ground. Maybe this is also an option for the 107?

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


Gruß,
Jörg

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Nov. 2020 13:38 #261557 von Rudiger
Jorg, daran hatte ich auch gestern gedacht durch die begrenzte hohe. Wie wurde das im Werk gemacht? Ich glaube der Motor ist an den cylinderkopfen zu breit um den nach unten auszubauen
Rudiger

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
01 Nov. 2020 15:14 - 01 Nov. 2020 15:16 #261564 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
Lifting the body off of the engine and subframe was also my preference, I have asked around but not found anyone who has actually done this to give advice.

One problem that would need to be solved is to first remove the steering box which is in the way, and it is much easier to remove the steering box once the engine is out of the car.

In the end neither way is easy, and since I have done it once before, perhaps better to stick with the method that worked last time.

Grand Prix now finished so back out to the car.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 01 Nov. 2020 15:16 von Racediagnostics.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Nov. 2020 19:09 #261576 von Chromix

Racediagnostics schrieb: I purchased this engine stand ..... Rather than this one ..... After watching this video .....

I wouldn't blame the engine stand for what happened. I mean, lifting up one leg of the engine stand while the engine is already resting on it ("It's no weight on the crane right now!"), was not a really good idea of "EricTheCarGuy".

Regards, Lutz

Alle Lebewesen außer den Menschen wissen, daß der Hauptzweck des Lebens darin besteht, es zu genießen.
Samuel Butler

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Nov. 2020 20:23 #261580 von wusel-53

Rudiger schrieb: Jim, to overhaul an engine is pretty straight forward. Basically intake manifold, heads and block. Get the specs and tolerances and you are good. WIS should be in eye side. :)

Remember wisely-53 Thorsten overhauled a transmission. He is a pencil pusher at the fed. Government. WIS will help.
Btw, I wouldn’t touch a damn automatic transmission with a 10 foot pole
Rudiger


Thanks Rudiger for "pencil-puscher" :laugh: :laugh: :laugh:

Viele Grüße

Thorsten

Man lernt nie aus
380SL (US-Version, Bj.84), Eura-Wohnmobil und ein ebike :-)
Folgende Benutzer bedankten sich: Rudiger

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
01 Nov. 2020 20:48 #261583 von Rudiger

wusel-53 schrieb:

Rudiger schrieb: Jim, to overhaul an engine is pretty straight forward. Basically intake manifold, heads and block. Get the specs and tolerances and you are good. WIS should be in eye side. :)

Remember wisely-53 Thorsten overhauled a transmission. He is a pencil pusher at the fed. Government. WIS will help.
Btw, I wouldn’t touch a damn automatic transmission with a 10 foot pole
Rudiger


Thanks Rudiger for "pencil-puscher" :laugh: :laugh: :laugh:


Thorsten, You are very welcome . :)
Folgende Benutzer bedankten sich: wusel-53

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
01 Nov. 2020 21:02 #261585 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
I had been hoping to leave the middle and back exhaust box in place, but realised today that the prop shaft nut is above the middle box and heat shield. I will have to rethink that plan, perhaps with a bit of leverage I may still be able to get to it. Has anyone else managed with the middle box in place?

Anyway today, lots more disassembly.

Steering drag link ball joint removed at one side to help with the clearance for the transmission.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Earth strap disconnected.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Heat shields out and right downpipe, the left downpipe is in a restricted place and does not want to come out yet.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Engine mount bolts next.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Then the engine dampers.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Throttle linkage, oil pressure gauge and coolant hoses disconnected.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Brake booster vac line.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Wiring harness at the front and rear disconnected.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



I remember when I put this engine in ten years ago that the crane chains came close to the fuel injector pipes so I decided to remove it first as its only held on by four nuts.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Folgende Benutzer bedankten sich: mike 560

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
01 Nov. 2020 21:22 #261587 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
I have a couple of other questions, first, should there be a rubber boot around the throttle lever in the bulkhead here?

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



And second, can the front pully be removed from the harmonic balancer by removing these smaller bolts? I was surprised to see that one was missing.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
02 Nov. 2020 13:22 - 02 Nov. 2020 13:23 #261640 von Marcel
Hi Jim,

around the lever there is a rubber boot, see on my 1986 300 SL

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.
Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.

Gruß Marcel
300 CE-24 Bj 7/90

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.

Dieser Beitrag enthält Bilddateien.
Bitte anmelden (oder registrieren) um sie zu sehen.

Letzte Änderung: 02 Nov. 2020 13:23 von Marcel.
Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
02 Nov. 2020 13:54 #261642 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
Thanks Marcel, yours looks the same as mine so puts my mind at rest, I thought perhaps there should also have been a second boot on the outer skin of the bulkhead.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
02 Nov. 2020 20:07 - 02 Nov. 2020 20:08 #261669 von Thomas2509
Hello Jim,

today I have removed my M110 (280SL) together with the transmission. Like you I did the whole work in my garage and I had no problems with the height. Probably I think that the M110 engine is a little longer than yours.

Greetings Thomas
Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.

Es grüßt herzlich
Thomas

Dieser Beitrag enthält einen Bildanhang.
Bitte anmelden (oder registrieren) um ihn zu sehen.

Letzte Änderung: 02 Nov. 2020 20:08 von Thomas2509.
Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
02 Nov. 2020 20:52 - 02 Nov. 2020 20:59 #261671 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
Day 4, I moved on to the transmission today. Drained the fluid.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Released the gear linkage.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Removed the front part of the cradle.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Kick-down wire removed.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Remainder of cradle removed.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Speedometer cable and PNDR switch harness released.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Prop-shaft coupling released.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



For the prop-shaft spline coupling.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Finally the torque converter was drained.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



That's all the prep work now almost complete.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 02 Nov. 2020 20:59 von Racediagnostics.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
02 Nov. 2020 20:56 - 02 Nov. 2020 20:57 #261673 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
A few more things.

Protection for the radiator support.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Make your bets now, will the engine come out with the bonnet on or not?

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



It's up as far as I dare.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 02 Nov. 2020 20:57 von Racediagnostics.

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
02 Nov. 2020 22:44 #261678 von Chromix
Uhh, I would be wary! Better ask your wife to help you to take the bonnet off.
At least I would try to hold it from the ceiling. Otherwise, if you interfere with one of the supports while taking the engine out, bad things could happen to it.

Regards, Lutz

Alle Lebewesen außer den Menschen wissen, daß der Hauptzweck des Lebens darin besteht, es zu genießen.
Samuel Butler
Folgende Benutzer bedankten sich: Racediagnostics

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
02 Nov. 2020 23:13 #261679 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
Good suggestion, I will take the air intake vents off so I can go a bit more vertical and also support the bonnet from the ceiling.

Taking the bonnet off with my wife would be a high risk, it is so easy to scratch or dent a wing etc. If she struggles with the weight.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
03 Nov. 2020 03:45 #261680 von Rudiger
Jim, do you have plenty of room in front? What’s your intended, swing engine and transmission side ways?
Rudiger

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
03 Nov. 2020 06:21 #261681 von Thomas2509
Jim, I really suggest to put off the bonnet.
It is easy to remove and you need the space.
And take a additional look to the transmission. I forgot one wiring harness connection at the transmission and damaged the connector.
Best regards Thomas

Es grüßt herzlich
Thomas

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
03 Nov. 2020 10:09 #261684 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
Hi Rudiger, once the engine is out I will push the car back out of the garage to give space to manoeuvre the engine.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

  • Racediagnostics
  • Autor
  • Offline
  • Elite
  • Elite
  • UK spec
Mehr
03 Nov. 2020 20:52 - 03 Nov. 2020 21:28 #261725 von Racediagnostics
Racediagnostics antwortete auf Engine rebuild with no former experience........
The first task this morning was to remove the air intake vents so that the bonnet could be lifted higher. The main problem doing this is due at least 50% of the pegs used in the plastic rivets disappearing.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



The car pushed out of the garage a bit to allow the engine hoist to be positioned.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



The bonnet support felt very secure in this position, ready to lift.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



It took nearly an hour to get the engine into this position, it kept jamming between the right exhaust manifold against the chassis rail and the bell housing on the steering box. In the end I had to remove the exhaust manifold on the right which took a at least 30 minutes due to the position of its fixing. You can also see from this picture it was wise to remove the fuel distributer etc.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



From then on it was straightforward to raise the engine, level it and drop the car onto its wheels then push it back out of the way.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Engine dropped onto a trolley.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Next I dragged the car lift back into place.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



I then assembled the engine stand and had a tidy up.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



You can see here the problem area where the bell housing fouled against the steering box. I will trim some of this off to improve clearance.

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.



I videoed the entire extraction but will need to edit/fast forward some sections as it's 90minutes long and rather boring.

Cheers
Jim

Dieses Bild ist für Gäste verborgen.
Bitte anmelden oder registrieren um das Bild zu sehen.


1979 450SL - 2002 XK8 4.2
Letzte Änderung: 03 Nov. 2020 21:28 von Racediagnostics.
Folgende Benutzer bedankten sich: mike 560

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
03 Nov. 2020 21:10 #261726 von Seewolf107
Jim, why dont you remove the steering Box?
It is not that hard.

Grüsse Claus
1966 Plymouth Belvedere 383, 300D 1983, 280CE W123

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Mehr
03 Nov. 2020 21:14 #261727 von markus1971
Hello Jim,

you did a great job! Can you estimate the high to the ceiling that is needed to remove the engine?

Best regards

Markus

Bitte Anmelden oder Registrieren um der Konversation beizutreten.

Moderatoren: RagettiObelix116
Ladezeit der Seite: 0.211 Sekunden
Powered by Kunena Forum
Cookies erleichtern die Bereitstellung unserer Dienste. Mit der Nutzung unserer Dienste erklären Sie sich damit der Datenschutzerklärung und der Verwendung von Cookies einverstanden.