560SL Rear End Rebuild

I am almost finished with rebuilding the rear end on my 1987 560SL.  Some aspects of this rebuild have been most difficult to get repair procedures.  I purchased the factory 2 volume chassis workshop procedures and this manual entirely skips discussing the rear trailing arms removal and rebuild.  I tried subscribing to startek but they removed me when they determined I was not a repair shop.  For instance in the following diagram:

photos.google.com/photo/AF1QipPPdsrFy7U2...l57ROjvRQetL7Noow41e
What is the torque for item 41 which is the nut?  I need specific torque specs for rear differential, rear sway bar, etc.  Rebuild included removing pinion shaft to replace seal and properly pre tensioning reinstall.  As I mentioned I am almost finished...  Also, if you can point me to where I can purchase complete workshop information, I would be eternally grateful.

photos.google.com/photo/AF1QipMHXZXDHebP...CbmgpvDjVkcHyV7A096K

photos.google.com/photo/AF1QipOEXmDWOI5K...o47eQK0dEFfp-RBXYMx4

…and whats your name ?!?

It woud be very nice if you could introduce you a Little bit at first!
 

Sure! My name is Bob Trautman from Texas. Purchased my 560sl approximately 7 years ago. Have been making steady repairs over the years. First major repair was when I changed my oil and I found this strange wire ground to the chassis. After reviewing electrical diagrams, I identified it as the oil level sensor connector. Now why in the world would someone ground this connector? I corrected the situation and plugged the oil level sensor back into the connector. 1 minute later I had a check engine light on. Eventually figured out the oil level sensor was defective. No problem, I will just replace it! I then learned I had to drop the oil pan....which required dropping the front subframe........Thus began my forray into the R107...... My biggest frustration with this car is german documentation regarding workshop repair procedures.........

For instance I own the two volume set of R107 chassis repair procedures. Nowhere in this 2 volume set does it address rear-end components such as R&R hub, trailing arm R&R, etc.......

SLSHOP has been most helpful in being able to source parts that are not available in the US.

Hello Bob
here you will find documents that may help you

sternzeit-107.de/de/slpedia/107sl-wsm

Stefan

Stefan, Thank you for this link. I see that this user interface was developed for the star link site for public. I have used the raw interface at star link and always was perplexed why there interface was so disjointed... This interface is SO much more useful to use!

I still did not find any information on what the torque spec and/or workshop procedure regarding the "WHEEL BEARING TO COUPLED TRANSVERSE CONTROL ARM NUT"

I may go begging to my local MB dealer and see if they will give me the information. The parts Department knows me very well..................................

Again, thank you for this interface. I will certainly use it in the future.

www.startekinfo.com/service/download-doc...GRAM/Chassis/B33.pdf

gruß
Stefan

Stefan, thank you for sending this. This is excellent information for the front end. I can't seem to find similar information for the rear end......

I've not checked it, but maybe you can find something there? www.tonk.ca/misc/index.html (Body/Chassis 1987 pdf)

...Bob, it would be very nice if you could sign your Threads with your first name like everyone does it here, i`m too lazy to look it up everytime !

Yes, I've checked there as well. No information.

Thanks,
Bob

Of Course!

Bob

Bob,

you can enter your given name in your profile so you "can not forget" your signatur in future.

Best regards

Hello Bob
I can't open the pictures, don't know exactly what you are looking for, also because of the translation

www.startekinfo.com/service/download-doc...GRAM/Chassis/B35.pdf

Gruss
Stefan

I am attaching a picture of EPC diagram.  The nut is item 41 that I need the torque spec on.  It is the caliper support spindle nut on the rear.

I'm not sure why the photo links would not open for you.  They are google photo links.

Also, I am getting different torque specs for the CV axle bolts to Differential side flanges.  Please confirm torque for these bolts.

There is also a rear differential bolt that is a double spline mushroom shape bolt that I can't find torque specs for either.

 

Ja Herr Lehrer, gern, Herr Lehrer

I’m confused by your response.  

Bitte immer freundlich bleiben

 

Ragetti wrote:

Bitte immer freundlich bleiben

Rolf,  Hope all is well!  You may not remember me but I purchased one of your interior temperature sensors for my 560SL.  I seem to recall the beach front property near you   

I am having a difficult time getting the information I asked about here.  I don't just want to guess on the reassembly.  Again hope you are well!
 

Hi Bob,

I found the requested information in the german workshop manual in chapter 35-035.

The nut has item nbr. 97, see attached screensots. There seems to be a special procedere not just a torque value.

Hope this helps,
Ralf

Ralf,

thank you so much! I will share this with my MB enthusiast friends! What manual did you find this information in? Is there an American version? I purchased a two volume 107 MB chassis set and this information was not in it.  I would like to purchase a copy of that manual if I can find it. 
May I ask one more favor from you?  What are the torque specs for the CV axle bolts to differential side flanges.  I am getting different numbers.

Again, thank you!